Polyphenylene oxide (PPO): properties and injection molding

PPO (polyphenylene oxide, also PPE) is an amorphous engineering plastic with low water absorption and heat resistance. Blends, limits, drying and molding.

Bemar Plast Team. Updated on .

PPO (polyphenylene oxide), also known as PPE (polyphenylene ether), is an amorphous engineering plastic with a glass transition temperature of around 215 °C (419 °F), very low water absorption and stable dielectric properties. In injection molding it is almost always used as a blend with polystyrene or other polymers (modified PPO), which makes it processable. Typical parts include electrical and electronic components, pump and plumbing parts, appliance components and automotive parts that need dimensional stability and resistance to hot water.

Background

Polyphenylene oxide was developed in the United States at General Electric: in 1956, chemist Allan Hay found a way to polymerize 2,6-dimethylphenol by oxidative coupling. The neat polymer reached the market in 1964 under the PPO trademark, followed in 1966 by polystyrene blends sold as Noryl™. Both trademarks now belong to SABIC, and other producers supply PPE and modified PPE under their own trade names.

Names, structure and grades

PPO and PPE refer to the same polymer, poly(2,6-dimethyl-1,4-phenylene ether). PPE is the correct chemical name; PPO started as a trade name and is still the term most buyers and molders use.

PPE is an amorphous polymer: it has no sharp melting point, its mold shrinkage is low and uniform, and parts hold their dimensions well. In its neat form, however, it has a very high melt viscosity and needs processing temperatures close to its degradation range. That is why injection molders almost always work with blends.

Main blends

  • PPE/PS (or PPE/HIPS): the most common modified PPO. PPE and polystyrene are miscible in all proportions: more PPE means higher heat resistance and higher cost, more PS means better flow. As a result, heat deflection temperature (HDT) varies widely from grade to grade.
  • PPE/PA: combines the dimensional and thermal stability of PPE with the oil and fuel resistance of polyamide (nylon). It is used for paintable body panels and parts exposed to high temperatures. Unlike the other blends, it absorbs moisture.
  • PPE/PP: improves chemical resistance and lowers density; typical uses include battery housings and wire and cable insulation.

Filled and modified grades

Glass-fiber-reinforced and mineral-filled grades are available to raise stiffness and heat resistance, along with halogen-free flame-retardant grades. Flammability ratings (for example UL 94) are stated by the resin supplier for each grade and wall thickness.

PPO properties: advantages

  • Heat resistance: the glass transition temperature of neat PPE is around 215 °C (419 °F); in blends, heat resistance depends on the PPE content.
  • Dimensional stability: low, uniform shrinkage, a low coefficient of thermal expansion and good creep resistance. Suitable for tight-tolerance parts.
  • Very low water absorption and excellent hydrolysis resistance: properties remain stable in humid environments, in hot water and in contact with steam.
  • Electrical properties: low dielectric constant and dissipation factor, stable across temperature, frequency and humidity.
  • Flammability: PPE forms a char when it burns, which makes halogen-free flame-retardant grades easier to formulate.
  • Low density for an engineering plastic, which helps reduce part weight.
  • Chemical resistance to water, salt solutions, dilute acids and bases, and many detergents.
  • Good toughness, retained at low temperatures in impact-modified grades.
  • Secondary operations: it welds well ultrasonically and can be painted, metallized and bonded.

PPO properties: disadvantages

  • Solvents: aromatic and chlorinated hydrocarbons, ketones and esters dissolve or swell modified PPO.
  • Stress cracking: some oils, greases and detergents can cause environmental stress cracking in loaded parts or parts with residual stress; compatibility must be tested.
  • UV exposure: without stabilizers, pigments or paint, it yellows and loses properties outdoors.
  • Neat PPE is hard to process: that is why it is used almost only as a blend.
  • Sensitivity to long barrel residence: long residence times and excessive temperatures degrade the material.
  • Cost is higher than for commodity polymers such as PP, PS and ABS.
  • Friction and wear: for sliding parts, POM or nylon is usually preferred.

Processing and injection molding

Modified PPO is processed mainly by injection molding; it is also extruded (profiles, sheet, cable jacketing) and thermoformed from sheet.

Drying

Although it absorbs very little water, modified PPO should be dried before molding: surface moisture on the pellets causes splay and cosmetic defects. Many PPE/PS datasheets specify 2-3 hours at 100-120 °C (212-248 °F); PPE/PP blends need lower temperatures, while PPE/PA blends are dried like a nylon. The correct values are always those in the datasheet of the selected grade.

Process settings

  • High melt temperatures, roughly 260-330 °C (500-625 °F) depending on the grade.
  • A hot mold, roughly 65-120 °C (150-250 °F), for good surface finish and low molded-in stress.
  • Short barrel residence times; during long stops, lower the barrel temperature or purge.
  • Generous radii and no sharp corners, to limit the stress concentrations that promote stress cracking.

Low, uniform shrinkage makes modified PPO a good fit for tight-tolerance parts and for large housings that must stay flat.

PPO at Bemar Plast

If your part is specified in PPO or modified PPO, we assess the material together with your engineering team, starting from the drawing, the requirements and the specified grade. All 13 of our injection molding lines are equipped with a dehumidifying dryer.

Applications of PPO

  • Electrical and electronics: connectors, terminal blocks, junction boxes, housings, coil bobbins, junction boxes for photovoltaic modules.
  • Plumbing and water treatment: pump housings, impellers, water meters, fittings and hot-water components. Some grades carry approvals for contact with drinking water.
  • Household appliances: washing machine, dishwasher and coffee machine parts, fans, housings.
  • Automotive: electrical components, housings, interior parts and, with PPE/PA blends, painted body panels.
  • Batteries and energy storage: housings, holders and separators for cells and modules.

PPO or another engineering plastic?

Modified PPO is a sound technical choice when a part needs dimensional stability, hydrolysis resistance and electrical properties at the same time, at moderate service temperatures. For higher temperatures or aggressive chemicals, PPS is often a better fit; for sliding parts or contact with oils and fuels, polyamides are worth evaluating. The final choice depends on the specific grade and should be confirmed by testing the actual part.

Frequently asked questions

What is the difference between PPO and PPE?

They are the same polymer: PPE (polyphenylene ether) is the chemical name, while PPO started as a trade name and stayed in common use. Modified PPO (mPPO or mPPE) refers to blends with polystyrene or other polymers, which are the form most used in injection molding.

Does PPO need drying before molding?

Yes, drying is recommended even though the material absorbs very little water, because surface moisture causes splay and cosmetic defects. Many PPE/PS datasheets specify 2-3 hours at 100-120 °C (212-248 °F); PPE/PA blends are dried like a nylon. Always follow the datasheet of the selected grade.

Is PPO resistant to hot water?

Yes: it absorbs very little water and has excellent hydrolysis resistance, which is why it is used in pumps, water meters and plumbing components. Parts in contact with drinking water need a grade with the approvals required in the target market, such as NSF/ANSI 61 in North America.

Which chemicals attack PPO?

Aromatic and chlorinated hydrocarbons, ketones and esters dissolve or swell modified PPO. Some oils, greases and detergents can cause environmental stress cracking in loaded parts, so compatibility should be tested on the actual component.

PPO or PPS: which one should I choose?

PPS suits higher service temperatures and aggressive chemical environments. Modified PPO is lighter, usually less expensive and a good fit when you need dimensional stability, hydrolysis resistance and good electrical properties at moderate temperatures.

Does Bemar Plast mold PPO parts?

We assess the material together with your engineering team, starting from the drawing, the part requirements and the specified grade. All 13 of our injection molding lines are equipped with a dehumidifying dryer.

Send us your drawing, and we will tell you how to mold it

We reply with a technical assessment and a quote. To prepare them, we need three pieces of information about your component.

  1. The part

    The 2D drawing or 3D model of the component.

    • STEP
    • IGES
    • PDF
  2. Material and annual volume

    The required material, or the part's operating conditions if the material has yet to be chosen. Then the approximate annual volume.

  3. Cosmetic requirements and tolerances

    Visible surfaces, color and finish, and the critical tolerances to be met.

If you do not have all the data yet, write to us anyway: we will define it together.

Hours
Monday–Friday, 8 a.m.–6 p.m. Italian time (2 a.m.–noon ET)